INSPECTION REPORT Type of Inspection: Condition Inspection OWNER: DATE: MAKE: HOURS: "N" #: SER. #: ­ DESCRIPTION A. PROPELLER GROUP 1.______ Inspect spinner and back plate 2.______ Inspect blades for nicks and cracks 3.______ Check for grease and oil leaks 4.______ Lubricate propeller per lubrication chart 5.______ Check spinner mounting brackets 6.______ Check propeller mounting bolts and safety 7.______ Inspect hub parts for cracks and corrosion B. ENGINE GROUP CAUTION: ground mags before working on engine 1.______ Remove engine cowl 2.______ Clean and check cowling for cracks, distortion and loose or missing fasteners 3.______ Drain oil sump 4.______ Clean suction oil strainer at oil change 5.______ Clean pressure oil strainer or change full flow oil filter element 6.______ Check oil temp. sender for leaks and security 7.______ Check oil lines and fittings for leaks, chafing, security, dents and cracks 8.______ Clean and check oil radiator cooling fins 9.______ Fill engine with oil per lubrication chart 10._____ Clean engine 11._____ Check condition of spark plugs, adjust gap to:______ clean, test, rotate 12._____ Check ignition harness and insulators 13._____ Check magneto points for proper clearance maintain at .018 +- .006 14._____ Check magneto for oil seal leaks 15._____ Check breaker felt for proper lubrication 16._____ Check distributor block for cracks, burned areas or corrosion 17._____ Check magnetos to engine timing Left______ Right _______ 18._____ Remove air filter and clean 19._____ Drain carburetor and clean inlet line fuel strainer 20._____ Check condition of carburetor heat air door and box 21._____ Check intake seal for leaks and clamps for tightness 22._____ Clean fuel screens 23._____ Clean and check gasolator 24._____ Inspect condition of fuel lines 25._____ Check fuel system for leaks 26._____ Check electric fuel pump for operation 27._____ Check engine controls throttle, carb heat, mixture, and prop 28._____ Inspect exhaust stacks, connections, gaskets 29._____ Inspect heat exchange, baffles and shrouds 30._____ Check breather tube for obstructions and security 31._____ Check crankcase for cracks, leaks, security of bolts 32._____ Check engine mounts for cracks and loose mountings 33._____ Check all engine baffles 34._____ Check firewall seals 36._____ Check condition and tension of alternator and drive belt 36._____ Check condition of starter 37._____ Check fluid in brake reservoir 38._____ Lubricate all controls 39._____ Inspect engine for general condition, loose parts, chafing, proper safties and proper installation 40._____ Check condition of alternator 41._____ Check vacuum pump and lines 42._____ Compression check #1______ #2______ #3 ______ #4 ______ 43._____ Grease starter gear with moly 44._____ Reinstall engine cowl C. CABIN GROUP 1._____ Inspect canopy and windows 2._____ Check upholstery for tear 3._____ Check seats, seat belts, shoulder straps 4._____ Check trim operation 5._____ Check rudder pedals 6._____ Check control column, systems and connection 7._____ Check landing, nav, cabin, and instrument lights 8._____ Check instrument, lines and attachments 9._____ Check gyro operation, and electric turn and bank 10.____ Check or replace gyro air filter 11.____ Clean or replace vacuum regulator filter 12.____ Check altimeter 13.____ Check operation of fuel selector valve 14.____ Check operation of engine primer 15.____ Check condition of heater controls 16.____ Check condition and operation air vents 17.____ Check flap operation 18.____ Check fuel drains 19.____ Lubricate aileron, flap and elevator controls 20.____ Check general condition uder panel for loose wires, chafing, etc. 21.____ Check brake cylinders for operation and leaks D. FUSELAGE AND EMPENNAGE GROUP 1._____ Remove inspection plates and panels 2._____ Check battery box, battery and cables 3._____ Check electronic installations 4._____ Check bulkheads and stringers for damage 5._____ Check antenna mounts and wiring 6._____ Check fuel lines and valves 7._____ Check vertical fin and rudder surfaces 8._____ Check rudder horn and attachment 9._____ Check vertical fin attachments 10.____ Check rudder bolts for wear 11.____ Check horizonal stabilizer and elevators 12.____ Check horizonal stabilizer attachment 13.____ Check elevator horn 14.____ Check elevator bolts for wear 15.____ Check elevator bell cranks and controls and trim system 16.____ Lubricate all bearings as needed 17.____ Check general condition of skin 18.____ Check doors, latches and hinges 19.____ Check wiring for damage and security 20.____ Check cables for damage, security and operation 21.____ Check cabin heater and controls 22.____ Service hydraulic brake system 23.____ Check drain holes in rudder bottom and fuselage 23.____ Reinstall inspection plates and panels E. WING GROUP 1._____ Remove inspection plates and fairings 2._____ Check surfaces and tip for damage and loose rivets and condition of walkways 3._____ Check aileron mounts and attachments 4._____ Check aileron bellcrank and control tubes 5._____ Check flaps and attachment for damages 6._____ Check all wing attachment bolts 7._____ Check fuel tanks and lines for leaks and chafing 8._____ Check fuel tank vents 9._____ Check pitot 10._____ Reinstall inspection plates F. LANDING GEAR GROUP 1._____ Check nose gear travel and damper tightness 2._____ Check main gear attachments 3._____ Check tires for cuts and wear 4._____ Remove wheel, clean, and repack bearings COTTER PINS IN AXLES? 5._____ Check wheels for cracks, corrosion and broken bolts 6._____ Check tire pressure_____ 7._____ Check brake lining and disc 8._____ Check brake lines 9._____ Check tailwheel assembly for integrity and grease tailwheel G. OPERATIONAL INSPECTION 1._____ Check fuel pump and fuel tank selector 2._____ Check fuel pressure 3._____ Check oil pressure and temperature 4._____ Check alternator output 5._____ Check manifold pressure 6._____ Check alternate air 7._____ Check vacuum gauge 8._____ Check gyros for noise and roughness 9._____ Check Cabin heat operation 10.____ Check magneto switch operation 11.____ Check magneto RPM variation Left_____ Right_____ Run up rpm_______ 12.____ Check throttle and mixture operation 13.____ Check propeller smoothness 14.____ Check electronic equipment operation: fuel gauges, tach, engine instrumensts 15.____ Check ELT for operation and battery date 16.____ Check static rpms 17.____ Check idle rpms H. GENERAL 1._____ A.D.s complied with 2._____ Manufacturers service letters complied with 3._____ Registration, Airworthiness Cerfificate, Operating Limitations Signature_________________________ Certificate No: