INSPECTION REPORT Type of Inspection: Condition Inspection
OWNER:
DATE:
MAKE:
HOURS:
"N" #:
SER. #:
DESCRIPTION
A. PROPELLER GROUP
1.______ Inspect spinner and back plate
2.______ Inspect blades for nicks and cracks
3.______ Check for grease and oil leaks
4.______ Lubricate propeller per lubrication chart
5.______ Check spinner mounting brackets
6.______ Check propeller mounting bolts and safety
7.______ Inspect hub parts for cracks and corrosion
B. ENGINE GROUP CAUTION: ground mags before working on engine
1.______ Remove engine cowl
2.______ Clean and check cowling for cracks, distortion and loose or missing fasteners
3.______ Drain oil sump
4.______ Clean suction oil strainer at oil change
5.______ Clean pressure oil strainer or change full flow oil filter element
6.______ Check oil temp. sender for leaks and security
7.______ Check oil lines and fittings for leaks, chafing, security, dents and cracks
8.______ Clean and check oil radiator cooling fins
9.______ Fill engine with oil per lubrication chart
10._____ Clean engine
11._____ Check condition of spark plugs, adjust gap to:______ clean, test, rotate
12._____ Check ignition harness and insulators
13._____ Check magneto points for proper clearance maintain at .018 +- .006
14._____ Check magneto for oil seal leaks
15._____ Check breaker felt for proper lubrication
16._____ Check distributor block for cracks, burned areas or corrosion
17._____ Check magnetos to engine timing Left______ Right _______
18._____ Remove air filter and clean
19._____ Drain carburetor and clean inlet line fuel strainer
20._____ Check condition of carburetor heat air door and box
21._____ Check intake seal for leaks and clamps for tightness
22._____ Clean fuel screens
23._____ Clean and check gasolator
24._____ Inspect condition of fuel lines
25._____ Check fuel system for leaks
26._____ Check electric fuel pump for operation
27._____ Check engine controls throttle, carb heat, mixture, and prop
28._____ Inspect exhaust stacks, connections, gaskets
29._____ Inspect heat exchange, baffles and shrouds
30._____ Check breather tube for obstructions and security
31._____ Check crankcase for cracks, leaks, security of bolts
32._____ Check engine mounts for cracks and loose mountings
33._____ Check all engine baffles
34._____ Check firewall seals
36._____ Check condition and tension of alternator and drive belt
36._____ Check condition of starter
37._____ Check fluid in brake reservoir
38._____ Lubricate all controls
39._____ Inspect engine for general condition, loose parts, chafing, proper safties and proper installation
40._____ Check condition of alternator
41._____ Check vacuum pump and lines
42._____ Compression check #1______ #2______ #3 ______ #4 ______
43._____ Grease starter gear with moly
44._____ Reinstall engine cowl
C. CABIN GROUP
1._____ Inspect canopy and windows
2._____ Check upholstery for tear
3._____ Check seats, seat belts, shoulder straps
4._____ Check trim operation
5._____ Check rudder pedals
6._____ Check control column, systems and connection
7._____ Check landing, nav, cabin, and instrument lights
8._____ Check instrument, lines and attachments
9._____ Check gyro operation, and electric turn and bank
10.____ Check or replace gyro air filter
11.____ Clean or replace vacuum regulator filter
12.____ Check altimeter
13.____ Check operation of fuel selector valve
14.____ Check operation of engine primer
15.____ Check condition of heater controls
16.____ Check condition and operation air vents
17.____ Check flap operation
18.____ Check fuel drains
19.____ Lubricate aileron, flap and elevator controls
20.____ Check general condition uder panel for loose wires, chafing, etc.
21.____ Check brake cylinders for operation and leaks
D. FUSELAGE AND EMPENNAGE GROUP
1._____ Remove inspection plates and panels
2._____ Check battery box, battery and cables
3._____ Check electronic installations
4._____ Check bulkheads and stringers for damage
5._____ Check antenna mounts and wiring
6._____ Check fuel lines and valves
7._____ Check vertical fin and rudder surfaces
8._____ Check rudder horn and attachment
9._____ Check vertical fin attachments
10.____ Check rudder bolts for wear
11.____ Check horizonal stabilizer and elevators
12.____ Check horizonal stabilizer attachment
13.____ Check elevator horn
14.____ Check elevator bolts for wear
15.____ Check elevator bell cranks and controls and trim system
16.____ Lubricate all bearings as needed
17.____ Check general condition of skin
18.____ Check doors, latches and hinges
19.____ Check wiring for damage and security
20.____ Check cables for damage, security and operation
21.____ Check cabin heater and controls
22.____ Service hydraulic brake system
23.____ Check drain holes in rudder bottom and fuselage
23.____ Reinstall inspection plates and panels
E. WING GROUP
1._____ Remove inspection plates and fairings
2._____ Check surfaces and tip for damage and loose rivets and condition of walkways
3._____ Check aileron mounts and attachments
4._____ Check aileron bellcrank and control tubes
5._____ Check flaps and attachment for damages
6._____ Check all wing attachment bolts
7._____ Check fuel tanks and lines for leaks and chafing
8._____ Check fuel tank vents
9._____ Check pitot
10._____ Reinstall inspection plates
F. LANDING GEAR GROUP
1._____ Check nose gear travel and damper tightness
2._____ Check main gear attachments
3._____ Check tires for cuts and wear
4._____ Remove wheel, clean, and repack bearings COTTER PINS IN AXLES?
5._____ Check wheels for cracks, corrosion and broken bolts
6._____ Check tire pressure_____
7._____ Check brake lining and disc
8._____ Check brake lines
9._____ Check tailwheel assembly for integrity and grease tailwheel
G. OPERATIONAL INSPECTION
1._____ Check fuel pump and fuel tank selector
2._____ Check fuel pressure
3._____ Check oil pressure and temperature
4._____ Check alternator output
5._____ Check manifold pressure
6._____ Check alternate air
7._____ Check vacuum gauge
8._____ Check gyros for noise and roughness
9._____ Check Cabin heat operation
10.____ Check magneto switch operation
11.____ Check magneto RPM variation Left_____ Right_____ Run up rpm_______
12.____ Check throttle and mixture operation
13.____ Check propeller smoothness
14.____ Check electronic equipment operation: fuel gauges, tach, engine instrumensts
15.____ Check ELT for operation and battery date
16.____ Check static rpms
17.____ Check idle rpms
H. GENERAL
1._____ A.D.s complied with
2._____ Manufacturers service letters complied with
3._____ Registration, Airworthiness Cerfificate, Operating Limitations
Signature_________________________ Certificate No: